IMETCO : Produits métalliques pour l'enveloppe du bâtiment

No 07 61 16 Toiture en tôle à baguette pincée du répertoire normatif de DCC

Une élégance à l'épreuve du temps et une performance qui a fait ses preuves font d'Imetco Series 300 le système de toiture métallique de choix

Pendant un quart de siècle, les toitures métalliques à joints debout Series 300MD ont protégé des bâtiments à travers l'Amérique du Nord. Ce panneau structural remarquable ajoute un impact visuel dynamique tout en fournissant des décennies de protection même dans les climats les plus rigoureux.

Series 300 est inspiré par la performance et est à la fine pointe de la technologie

  • Long-term weather-tight performance à long terme
  • Custom trim and flashing details available
  • One-piece clip allows unlimited thermal movement
  • Rigorously tested against leaks and hurricane-force winds
  • Ideal for structural and/or architectural applications
  • Can be installed over open purlins or solid decks
  • Suitable for slopes as moderate as ¼:12, on steeper slopes, or vertically as a wall panel
  • 2-3/8" symmetrical seam with a separate, easy-to-install seam cap
  • Factory-applied hot-melt sealant that remains isolated from the clip
  • 3/8" clearance between panel and substrate promotes ventilation
  • 12-inch, 16-inch, and 18-inch panel widths
  • Wide variety of materials and colors

Unlimited Thermal Movement and Watertight Performance

The dynamic nature of a metal roof is embraced and facilitated by the Series 300 system. The unique one-piece concealed clip, made of heavy 16-gauge galvanized or stainless steel, is designed to provide maximum structural integrity while allowing unlimited thermal movement. The clip also elevates the panel 3/8-inch off the substrate to allow for air movement.

The one-piece clip, isolated seam sealant, custom trim, flashing, and system details all work together to accommodate the natural expansion and contraction of metal that occurs when it is exposed to varying temperatures. Each Series 300 roof is engineered for unlimited thermal movement to maintain the roof's structural integrity and provide a lifetime of watertight protection.

  • Specialty Manufacturing Options
  • Curving (convex, concave and "S" curves)
  • Tapering (to more than 80-feet in length)
  • Long panel factory manufacturing (up to 85 feet)
  • On-site fabrication of factory-quality straight or curved panels is available
  • The Installer's Advantage
  • Sleek, balanced, proportional look that complements any design
  • No interlocking male/female seams to worry about gives installers better control over when and where panels are installed
  • Install panels in either direction, or both directions, at any time
  • Start from any point on the roof
  • Run simultaneous crews to cut completion time in half
  • Work around roof protrusions and other obstacles
  • Mechanical seamer quickly and permanently seals the seam caps at a rate of 60 feet per minute, and runs in both directions
  • Reduces waste since each piece of a cut panel can be used for the opposite sides of a detail condition
  • If a panel needs to be removed or replaced, ONLY that panel needs to be removed or replaced - not every other panel between it and the roof's edge

brochure (PDF:2.9Mb)


  • 20-year finish warranty for Kynar 500® fluorocarbon coatings
  • Materials and workmanship warranty
  • Watertight warranty for qualified applications

Series 300 Architectural Specification available on request.

*Sample warranties are available. We encourage inclusion of warranty samples in specifications to streamline the bidding process. Kynar® is a registered trademark of Elf Atochem North America Inc.


Explor IMETCO : Produits métalliques pour l'enveloppe du bâtiment


Suivre les liens ci-dessous pour en savoir plus sur IMETCO : Produits métalliques pour l'enveloppe du bâtiment, demander un soumission et commander des échantillons.


Projets de référence

Voir Tous les Projets de Référence